Steps to Create a Unicorn Horn Flower Crown

Since who should have to decide in between a flower crown and a unicorn horn? Kaia really wished to use both for her Birthday, and this is what I ended up with.

When she initially informed me she wished to be a unicorn for her Birthday party, I started poking around the Web, attempting to figure something out. I was truly disappointed with exactly what I discovered. I didn't want her to be encumbered by a huge, hot, large outfit for her indoor party. I desired something she might don on her own when she wished to play. I didn't desire a modeling clay horn held on with an "undetectable" flexible band. These just don't appear useful to me for a young kid. I wanted a horn that would go on easily and comfortably, one that was light-weight, was not fragile, and would remain in place well on her head while she cantered around your house extremely, rearing and leaping. When you position a unicorn horn on a 4 year old, due to the fact that you know that is what is going to take place. (Omygosh, she's practically four!) I believe I really achieved all these standards I set myself, and I am actually happy with how the entire thing came together, (and so is she!).

When I made the horn, I was thinking I would experiment a bit, begin figuring things out. I didn't expect to be delighted with the first thing I twiddled with, so I'm stuck with no pictures. I made a paper design in order to do this tutorial. Not the prettiest pictures, however hopefully they a minimum of make the process simple to see.

You will require:.

Craft Felt in Various Colours.
Packing.
Sewing Thread and Needle.
Additional Strong Quilting Thread.
Small Length of Elastic.
Headband.
Hot glue.
Scissors.
Plastic Gems.
Material Leaves (Or Make Felt Leaves).

I used sparkly white craft felt for her horn. Aside from that it is, undoubtedly, sparkly, the sparkle felt is rather a bit stiffer. Cut out a slim triangle and fold it in half lengthwise, right sides together. Stitch up the open long side, marked with sharpy in the following pictures. Leave the bottom open. (That triangle was expected to be relatively in proportion. The real thing was, I swear. Pretend that it is reasonably symmetrical, fine? Thanks.).

Trim off excess fabric, and turn right-side-out. Utilizing extra strong quilting thread, cut a long piece, (enough to wrap your spirals,) and knot off completion. Make it a great, big knot, you do not want it to pull through the felt as soon as there is tension on it. Run the thread out near the idea of the horn from within. (Not at the tip.) Pull everything the way through, so that knot is the only part left inside. Things the horn as tightly as you can, I utilized polyfill stuffing. If necessary, cut the bottom to even it out.

Start covering the thread down the horn in a spiral, firmly enough to leave an excellent indent. This will give your horn a good spiraled shape, and keep the thread from slipping and moving around on the horn. (This was the part I was most uncertain about. I stressed that the fabric would lot, or that the thread would not be strong enough to pull securely, or that it would not stay in location. None of those worries came to light, it worked effectively.) Connect your thread off inside, near the bottom of the horn. Put your horn on another piece of matching felt, trace the bottom circle, and cut it out.

Starting from the within, wrap stitches around the edges of your felt, stitching the circle to the bottom of the horn, and connect it off. Aim to hide your knot inside, or a minimum of away from the edge.

I attached it to a great, wide, cloth-covered headband that we found at a dollar shop. To do so, measure a piece of elastic around the center of the headband to obtain your length, then make it a bit smaller sized so that it will extend comfortably into place. Sew the flexible ends together to form a loop. Sew the elastic to the bottom of the horn. Take care to sew the flexible all the method to the edges of the horn, or the base will pull up at the front and back. Make sure that the joint holding the elastic together gets sewn to the horn, this method it will end up on top of the headband, rather of as an uneasy swelling against your child's get redirected here head.

Your unicorn horn is complete! Oh, wait ... * ehem * Anyway, when on the headband, I included a little hot glue under the edges of the horn to assist keep it from wobbling any.

Cut a range of flowers out of the coloured felt. I have actually no concept how well hot glue works on wool felt, however it works astonishingly on eco felt. For the large yellow flower, I just cut a lot of strips of felt, folded them in half, then added them all together by their ends with a little thread.

Hot glue the flowers all over the headband, then hot glue the plastic gems to the centers. Ensure to overlap the base of the horn a bit and cover up the rubber band. You are the proud new owner of a unicorn horn flower crown!

I had a very tough time keeping her still long enough to take any pictures ...

Her rainbow unicorn tail is now complete, too, and I have a full blown unicorn galloping around your home all the time. Discover that tutorial here. By the method, it would be actually simple to stick a couple ears in there in the middle of the flowers. Inning accordance with Kaia, nevertheless, she currently has 2 ears and didn't desire anymore. (Do not take a look at me ... she uses a lot of other animal ears, my reasoning does seldom have much result on her, however.).

Because you know that is what is going to happen when you place a unicorn horn on a 4 year old. When I made the horn, I was thinking I would experiment a bit, start figuring things out. Make sure that the seam holding the elastic together gets sewn to the horn, this way it will end up on top of the headband, instead of as an uncomfortable lump against your child's head.

Make sure to overlap the base of the horn a bit and cover up the elastic band. You are the proud new owner of a unicorn horn flower crown!